Learning the Basics of Installing a Bathtub
Learning the Basics of Installing a Bathtub
Blog Article
The writer is making several great observations regarding Installing A Bathtub in general in this content which follows.
Setting up a tub isn't exactly brain surgery, yet it does call for solid plumbing, carpentry, and also often, tiling skills. Replacing an old bath tub with a new one is additionally a reasonably difficult project. If the old tub is easily available, the project can relocate quickly; if you have to open a wall to get rid of the old tub as well as position the new tub, the task is much harder. In either situation, the task is within a home handyman's abilities, although you will require a helper to vacate the old tub and also set in the brand-new one. Ensure you have actually certified yourself for the job as well as fit attempting it. As opposed to employing a professional to take control of a halfway-completed project, it is much better to take into consideration using one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This post will help you install a new tub in your bathroom if you have actually already acquired a brand-new bathtub as well as don't require to alter the arrangement of your previous water pipes.
Your tools as well as product list ought to consist of the following:
Planning for the Installment
First of all, the supporting frame supplied with the bathroom ought to be fitted (if required) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is necessary to make sure that if the faucet features a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets unit to prevent pressure on the bath tub.
Fit the versatile tap adapters to the bottom of the two faucets making use of 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet via the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you make use of all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to now prepare to be suited its last position.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you should do is disconnect the water. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The process of eliminating the existing faucets can be fairly bothersome as a result of the limited access that is frequently the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a cloth prepared for the staying water that will originate from the pipelines. Once the supply pipes have been removed, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning during this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old sealing compound.
Before carrying on to fit the brand-new taps, contrast the pipeline links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Bath tub
Utilizing the two wood boards under its feet, place the bath tub in the required position. The wooden boards are handy in uniformly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto four small factors.
The following goal is to guarantee that the tub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the bathtub up until the level checks out degree.
To install faucets, fit all-time low of the furthest versatile faucet connector to the suitable supply pipe by making a compression sign up with; then do the exact same for the other faucet.
Turn on the supply of water and also examine all joints as well as new pipework for leaks and tighten them if required. Fill up the tub as well as likewise examine the overflow electrical outlet and the normal electrical outlet for leakages.
Ultimately, fix the bath paneling as described in the manufacturer's instruction manual. Tiling as well as sealing around the bathtub should wait till the bath tub has been made use of at the very least when as this will settle it right into its final setting.
Suitable New Taps
If the tails of the new faucets are plastic, then you will need a plastic port to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end supplies a connection to the current supply pipes.
If you need to fit a monobloc, then you will need reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the tap in the installing opening in the bath/basin making sure that the washing machines are in place in between the faucet and the sink. Secure the faucet in place with the manufacturer given backnut. When the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical tap ports. The former kind needs to be connected to the faucet ends initially, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bath satisfies the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to fracture a stiff seal, creating the water to pass through the wall surface in between the bath and the tiling, bring about complications with moisture as well as possible leaks to the ceiling below.
You can pick from a selection of coloured sealants to blend in your fixtures and also installations. They are offered in tubes and cartridges, and are capable of sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to sealing, to enable the activity experienced when the tub is in use. The sealer can fracture fairly early if you do not think about this activity prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally quickly available on the market. It is advisable to fit the floor tiles making use of water-resistant or water resistant adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were made aware of that report about A Step-by-Step Guide to Installing a Bathtub through a friend on our other blog. Do you know about somebody who is serious about the subject? Do not hesitate to share it. I am grateful for your time. Visit us again soon.
Secure fix? Call. Report this page